Minimoog PCB dimensions:

1) Board #1 Oscillator:

   Drawing PIC 2, viewed from component side of board
   
   First board that I measured:
   
   A)	0.7"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	3.37"	
   C)	0.7"  (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	1.23" (left edge to ctr of mtg hole)
   E)	Didn't measure	
   F)	1.36" (right edge to ctr of mtg hole)
   G)	Didn't measure
   H)	5.675" (top edge to bottom edge)
   J)	3.658" (gap between finger sections)
   K)	3.39"
   W)	11 7/8"
   
   Also measured distance between ctrs of closest 
   fingers of two connectors as 3.75"
   
   Second board that I measured (MM ser 4949):
   
   A)	0.7"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	3.375"	
   C)	0.714" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	1.22" (left edge to ctr of mtg hole)
   E)	0.215" (top edge to ctr of mtg hole)	
   F)	1.35" (right edge to ctr of mtg hole)
   G)	0.21" (top edge to ctr of mtg hole)	
   H)	5.673" (top edge to bottom edge)
   J)	3.67" (gap between finger sections)
   K)	3.375"
   W)	11.834" (didn't measure, A+B+J+K+C)
   
   
   
2) Board #2 Contour:

   Drawing PIC 2, viewed from foil side of board
   
   First board that I measured:
 
   A)	0.395" (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	2.12"  (smaller connector pcb section width)
   C)	2.75" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	0.29" (left edge to ctr of mtg hole)
   E)	0.22" (top edge to ctr of mtg hole)	
   F)	1.0" (right edge to ctr of mtg hole)
   G)	0.22" (top edge to ctr of mtg hole)	
   H)	5.225" (top edge to bottom edge)
   J)	1.125" (gap between finger sections)
   K)	3.367"
   W)	9.75"
   
   Also measured distance between ctrs of closest 
   fingers of two connectors as 1.2"

   Second board that I measured (MM ser 4949):
 
   A)	0.43"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	2.096" (smaller connector pcb section width)
   C)	2.734" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	0.32" (left edge to ctr of mtg hole)
   E)	0.20" (top edge to ctr of mtg hole)	
   F)	1.04" (right edge to ctr of mtg hole)
   G)	0.20" (top edge to ctr of mtg hole)	
   H)	5.214" (top edge to bottom edge)
   J)	1.133" (gap between finger sections)
   K)	3.384"
   W)	9.79" (didn't measure, A+B+J+K+C)
   

   3) Board #3 Power Supply:

   Drawing PIC 1, viewed from foil side of board
   
   First board that I measured:
   
   A)	2.0"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	3.38"	
   C)	1.325" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	1.9" (left edge to ctr of mtg hole)
   E)	0.22" (top edge to ctr of mtg hole)	
   F)	1.6" (right edge to ctr of mtg hole)
   G)	Didn't measure
   H)	5.23" (top edge to bottom edge)
   W)	6 11/16"
   
   Second board that I measured (MM ser 4949):
   
   A)	2.0"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	3.37"	
   C)	1.30" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	1.87" (left edge to ctr of mtg hole)
   E)	0.25" (top edge to ctr of mtg hole)	
   F)	1.61" (right edge to ctr of mtg hole)
   G)	0.25" (top edge to ctr of mtg hole)
   H)	5.22" (top edge to bottom edge)
   W)	6.67" (didn't measure, A+B+C)

   
4) Board #4 Filter:

   Drawing PIC 1, viewed from foil side of board
   
   First board that I measured:

   A)	1.8"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	3.368"	
   C)	3.01" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   D)	1.5" (left edge to ctr of mtg hole)
   E)	3/16" (top edge to ctr of mtg hole)	
   F)	2 11/16" (right edge to ctr of mtg hole)
   G)	3/16" (top edge to ctr of mtg hole)
   H)	5.68" (top edge to bottom edge)
   W)	8 3/16"
   
   Second board that I measured (MM ser 4949):
   
   A)	1.79"  (pcb is cut right next to last edge finger.
			   from that cut to left edge of pcb)
   B)	3.38"	
   C)	3.00" (pcb is cut right next to last edge finger.
			   from that cut to right edge of pcb)
   W)	8.17" (didn't measure, A+B+C)

   
5) Board #5 Rectifier board:  2.69" x 3.875"

6) Board #6 Octave Buffer board:	1.6" x 2.0" (not measured, scaled 
					 from pcb layout in manual using 0.1" pin spacing)